Sail E0 Webinar

MCQs

Total Questions : 1798 | Page 175 of 180 pages
Question 1741. 3. The combination set can be used to
  1.    Check angular surfaces
  2.    Draw circles and arcs
  3.    Scribe lines
  4.    All of the above
 Discuss Question
Answer: Option A. -> Check angular surfaces
Question 1742. 4. Before drilling at a point, it should be ensured that
  1.    Punch mark has been made at the point
  2.    Position of point has been marked by two intersecting lines
  3.    Centre drill has been used at the point
  4.    Diameters have been located
 Discuss Question
Answer: Option C. -> Centre drill has been used at the point
Question 1743. 5. Surface roughness on a drawing is rep resented by
  1.    Triangles
  2.    Circles
  3.    Squares
  4.    Rectangles
 Discuss Question
Answer: Option A. -> Triangles
Question 1744. 7. A bore of 14.67 mm in a workpiece can be measured by
  1.    Steel rule
  2.    Vernier caliper
  3.    Pneumatic gauge
  4.    Micrometer
 Discuss Question
Answer: Option D. -> Micrometer
Question 1745. 1. Wire is fabricated by the following process
  1.    Drawing
  2.    Extrusion
  3.    Piercing
  4.    Rolling
 Discuss Question
Answer: Option A. -> Drawing
Question 1746. 6. Expressing a dimension as 32.5/32.3 mm is the case of
  1.    Unilateral tolerance
  2.    Bilateral tolerance
  3.    Limiting dimension
  4.    All of the above
 Discuss Question
Answer: Option C. -> Limiting dimension
Question 1747. 0. In banking operation, the force on punch depends upon
  1.    Sheet thickness
  2.    Clearance
  3.    Diameter of punch
  4.    All of the above
 Discuss Question
Answer: Option D. -> All of the above
Question 1748. 8. Ceramic tool inserts are fixed to tool holder by following process
  1.    Brazing
  2.    Soldering
  3.    Welding
  4.    Clamping
 Discuss Question
Answer: Option A. -> Brazing
Question 1749. 9. Sintering is used for
  1.    Fixing to91 inserts on tool holders
  2.    Manufacturing cutting tools
  3.    Heating the powdered metal below its melting point
  4.    Manufacturing powdered metal
 Discuss Question
Answer: Option C. -> Heating the powdered metal below its melting point
Question 1750. 2. In equation VT^n= C, value of n depends on
  1.    Material of workpiece
  2.    Material of tool
  3.    Condition of machine
  4.    Working conditions
 Discuss Question
Answer: Option B. -> Material of tool

Latest Videos
Chapter 1 - GLOBAL STEEL SCENARIO & INDIAN STEEL INDUSTRY Part 1 : (13-04-2024) INDUSTRY AND COMPANY AWARENESS (ICA)
Direction Sense Test Part 1 Reasoning (Hindi)
Chapter 1 - RMHP / OHP / OB & BP Part 1 : (14-02-2024) GPOE
Cube & Cuboid Part 1 Reasoning (Hindi)
Data Interpretation (DI) Basic Concept Reasoning (Hindi)
Counting Figures Part 1 Counting Of Straight Lines Reasoning (Hindi)
Sail E0 free webinar Webinars
Real Numbers Part 7 Class 10 Maths
Real Numbers Part 1 Class 10 Maths
Polynomials Part 1 Class 10 Maths

Latest Test Papers

DSP Combined 1 Free Revision Test SAIL JO E-0
GPOE / GPA Combined 1 Free Revision Test SAIL JO E-0
BSP Plant Specific Review Test SAIL JO E-0
BSL Combined 1 Free Revision Test SAIL JO E-0
GFM Combined 1 Free Revision Test SAIL JO E-0