Sail E0 Webinar

MCQs

Total Questions : 1798 | Page 2 of 180 pages
Question 11. The increase in depth of cut and feed rate _________ surface finish.
  1.    Improves
  2.    Deteriorates
  3.    Does not effect
  4.    None of these
 Discuss Question
Answer: Option B. -> Deteriorates
Question 12. Larger end cutting edge angle _________ tool life.
  1.    Increases
  2.    Decreases
  3.    Does not effect
  4.    None of these
 Discuss Question
Answer: Option A. -> Increases
Question 13. Tool signature consists of __________ elements.
  1.    Two
  2.    Four
  3.    Five
  4.    Seven
 Discuss Question
Answer: Option D. -> Seven
Question 14. The lead screw of a lathe has _________ threads.
  1.    Single start
  2.    Double start
  3.    Multi-start
  4.    Any one of these
 Discuss Question
Answer: Option A. -> Single start
Question 15. A broach has
  1.    Roughing teeth
  2.    Semi-finishing teeth
  3.    Finishing teeth
  4.    All of these
 Discuss Question
Answer: Option D. -> All of these
Question 16. A taper tap has
  1.    Its end tapered for about three or four threads
  2.    Its end tapered for about eight or ten threads
  3.    Full threads for the whole of its length
  4.    None of the above
 Discuss Question
Answer: Option B. -> Its end tapered for about eight or ten threads
Question 17. In a plain milling machine, the table can be moved
  1.    Longitudinally
  2.    Crosswise
  3.    Vertically
  4.    All of these
 Discuss Question
Answer: Option D. -> All of these
Question 18. The type of tool used on milling machine and broaching machine is
  1.    Single point cutting tool
  2.    Two point cutting tool
  3.    Three point cutting tool
  4.    Multi-point cutting tool
 Discuss Question
Answer: Option D. -> Multi-point cutting tool
Question 19. Cast iron during machining produces
  1.    Continuous chips
  2.    Discontinuous chips
  3.    Continuous chips with built-up edge
  4.    None of these
 Discuss Question
Answer: Option B. -> Discontinuous chips
Question 20. The ductile materials, during machining, produce
  1.    Continuous chips
  2.    Discontinuous chips
  3.    Continuous chips with built up edge
  4.    Either (A) or (C)
 Discuss Question
Answer: Option D. -> Either (A) or (C)

Latest Videos
Chapter 1 - GLOBAL STEEL SCENARIO & INDIAN STEEL INDUSTRY Part 1 : (13-04-2024) INDUSTRY AND COMPANY AWARENESS (ICA)
Direction Sense Test Part 1 Reasoning (Hindi)
Chapter 1 - RMHP / OHP / OB & BP Part 1 : (14-02-2024) GPOE
Cube & Cuboid Part 1 Reasoning (Hindi)
Data Interpretation (DI) Basic Concept Reasoning (Hindi)
Counting Figures Part 1 Counting Of Straight Lines Reasoning (Hindi)
Sail E0 free webinar Webinars
Real Numbers Part 7 Class 10 Maths
Real Numbers Part 1 Class 10 Maths
Polynomials Part 1 Class 10 Maths

Latest Test Papers

Pie Chart - Test Paper 1 Data Interpretation Reasoning & DI
Tabulation - Test Paper 2 Data Interpretation Reasoning & DI
Test Paper 1 Direction Sense Test Reasoning & DI
ICA , RDIC,GFM Free Modal Test Paper - Non - Technical Branch Old Syllabus 2022 - SAIL Junior Officer E0
GFM Combined 1 Free Revision Test SAIL JO E-0