Sail E0 Webinar

MCQs

Total Questions : 885 | Page 81 of 89 pages
Question 801. Which command loads a new version of the Cisco IOS into a router?
  1.    copy ftp flash
  2.    copy flash tftp
  3.    copy tftp flash
  4.    copy flash ftp
 Discuss Question
Answer: Option C. -> copy tftp flash
Question 802. Which three commands can be used to check LAN connectivity problems on a router?1. show interfaces2. show ip route3. tracert4. ping5. dns lookups
  1.    None of these
  2.    1 ,2 and 4
  3.    3 and 5
  4.    2 and 5
 Discuss Question
Answer: Option B. -> 1 ,2 and 4
Question 803. If you want to have more than one Telnet session open at the same time, what keystroke combination would you use?
  1.    Tab+Spacebar
  2.    Ctrl+Shift+X, then 6
  3.    Ctrl+Shift+6, then X
  4.    Ctrl+X, then 6
 Discuss Question
Answer: Option C. -> Ctrl+Shift+6, then X
Question 804. You are unsuccessful in telnetting into a remote device. What could the problem be?1. IP addresses are incorrect.2. Access control list is filtering Telnet.3. There is a defective serial cable.4. The VTY password is missing.
  1.    1 only
  2.    2 and 4 only
  3.    3 only
  4.    All of these
 Discuss Question
Answer: Option B. -> 2 and 4 only
Question 805. You are troubleshooting a connectivity problem in your corporate network and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. What IOS user exec command should you issue?
  1.    Router> ping
  2.    Router> trace
  3.    Router> show ip route
  4.    Router> show interface
 Discuss Question
Answer: Option B. -> Router> trace
Question 806. What should the configuration register value be after you successfully complete the password recovery procedure and return the router to normal operation?
  1.    0x2142
  2.    0x2101
  3.    0x2100
  4.    0x2102
 Discuss Question
Answer: Option D. -> 0x2102
Question 807. The configuration register setting of 0x2102 provides what function to a router?
  1.    Tells the router to look in NVRAM for the boot sequence
  2.    Provides password recovery
  3.    Boots the IOS from a TFTP server
  4.    Tells the router to boot into ROM monitor mode
 Discuss Question
Answer: Option A. -> Tells the router to look in NVRAM for the boot sequence
Question 808. Which command displays the configuration register setting?
  1.    show flash
  2.    show boot version
  3.    show version
  4.    show ip route
 Discuss Question
Answer: Option C. -> show version
Question 809. You telnet to a router and make your necessary changes; now you want to end the Telnet session. What command do you type in?
  1.    exit
  2.    disable
  3.    close
  4.    disconnect
 Discuss Question
Answer: Option A. -> exit
Question 810. What does the command o/r 0x2142 provide?
  1.    It is used to bypass the configuration in NVRAM.
  2.    It is used to view the lost password.
  3.    It is used to restart the router.
  4.    It is used to enter ROM Monitor mode.
 Discuss Question
Answer: Option A. -> It is used to bypass the configuration in NVRAM.

Latest Videos
Chapter 1 - GLOBAL STEEL SCENARIO & INDIAN STEEL INDUSTRY Part 1 : (13-04-2024) INDUSTRY AND COMPANY AWARENESS (ICA)
Direction Sense Test Part 1 Reasoning (Hindi)
Chapter 1 - RMHP / OHP / OB & BP Part 1 : (14-02-2024) GPOE
Cube & Cuboid Part 1 Reasoning (Hindi)
Data Interpretation (DI) Basic Concept Reasoning (Hindi)
Counting Figures Part 1 Counting Of Straight Lines Reasoning (Hindi)
Sail E0 free webinar Webinars
Real Numbers Part 7 Class 10 Maths
Real Numbers Part 1 Class 10 Maths
Polynomials Part 1 Class 10 Maths

Latest Test Papers

DSP Combined 1 Free Revision Test SAIL JO E-0
GPOE / GPA Combined 1 Free Revision Test SAIL JO E-0
BSP Plant Specific Review Test SAIL JO E-0
BSL Combined 1 Free Revision Test SAIL JO E-0
GFM Combined 1 Free Revision Test SAIL JO E-0