Sail E0 Webinar

MCQs

Total Questions : 540 | Page 46 of 54 pages
Question 451. These types of pipes are generally connected with bell and spigot joints or flanged joints:
  1.    Soil and waste
  2.    Gas and soil
  3.    Water and steam
  4.    Water and gas
 Discuss Question
Answer: Option D. -> Water and gas
Question 452. The ________ tool on the Dimension tool bar places the length of an arch on a drawing.
  1.    Diameter
  2.    Radius
  3.    Arc Length
  4.    Arc Radius
 Discuss Question
Answer: Option C. -> Arc Length
Question 453. An engineer's scale would be used to measure lines on a drawing where the scale factor reads ________.
  1.    1" = 100'
  2.    3/4" = 1'-0"
  3.    1/4" = 1'-0"
  4.    1/8" = 1'-0"
 Discuss Question
Answer: Option A. -> 1" = 100'
Question 454. Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
  1.    Type 3 forward slash and enter
  2.    Type 3 and try to use the Dynamic Input readout to find the end point
  3.    Type @3
  4.    Type 3 back slash and enter
 Discuss Question
Answer: Option C. -> Type @3
Question 455. These are special installations of stone or concrete marking the locations of points accurately determined by precise surveying:
  1.    Topographic marks
  2.    Pillars
  3.    Monuments
  4.    Hatches
 Discuss Question
Answer: Option C. -> Monuments
Question 456. In this type of view, the cutting plane line indicates both the location of the cutting plane and the direction of sight:
  1.    Revolved section
  2.    Partial section
  3.    Removed section
  4.    Auxiliary section
 Discuss Question
Answer: Option D. -> Auxiliary section
Question 457. This is formed where three or more surfaces intersect:
  1.    Vertex
  2.    Oblique
  3.    Line
  4.    Edge
 Discuss Question
Answer: Option A. -> Vertex
Question 458. The Press-Pull tool will ________ the face of a solid model in the direction it faces.
  1.    None of these
  2.    Spiral
  3.    Taper
  4.    Extrude
 Discuss Question
Answer: Option D. -> Extrude
Question 459. When designing a home for a client, one of the most important pre-design considerations that an architect needs to address is ________.
  1.    Whether or not there is a curb and gutter system
  2.    The nearest grocery store
  3.    The site on which the house is to sit
  4.    How much money the client is willing to spend
 Discuss Question
Answer: Option C. -> The site on which the house is to sit
Question 460. This material is used in masonry construction, most commonly for ornamental facing:
  1.    Face brick
  2.    Aggregate
  3.    Clay tile
  4.    Natural stone
 Discuss Question
Answer: Option D. -> Natural stone

Latest Videos
Chapter 1 - GLOBAL STEEL SCENARIO & INDIAN STEEL INDUSTRY Part 1 : (13-04-2024) INDUSTRY AND COMPANY AWARENESS (ICA)
Direction Sense Test Part 1 Reasoning (Hindi)
Chapter 1 - RMHP / OHP / OB & BP Part 1 : (14-02-2024) GPOE
Cube & Cuboid Part 1 Reasoning (Hindi)
Data Interpretation (DI) Basic Concept Reasoning (Hindi)
Counting Figures Part 1 Counting Of Straight Lines Reasoning (Hindi)
Sail E0 free webinar Webinars
Real Numbers Part 7 Class 10 Maths
Real Numbers Part 1 Class 10 Maths
Polynomials Part 1 Class 10 Maths

Latest Test Papers

DSP Combined 1 Free Revision Test SAIL JO E-0
GPOE / GPA Combined 1 Free Revision Test SAIL JO E-0
BSP Plant Specific Review Test SAIL JO E-0
BSL Combined 1 Free Revision Test SAIL JO E-0
GFM Combined 1 Free Revision Test SAIL JO E-0