Sail E0 Webinar

MCQs

Total Questions : 3218 | Page 319 of 322 pages
Question 3181. Bernoulli’s equation is dependent on the__________________?
  1.    First law of thermodynamics
  2.    Third law of thermodynamics
  3.    Law of conservation of momentum
  4.    None of these
 Discuss Question
Answer: Option D. -> None of these
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 3182. Pressure difference between two points in vessels, pipelines or in two different pipelines can be measured by a differential manometer. The pressure difference measured as the mm of water column in case of mercury-water, differential manometer is equal to (where, H = difference in height of mercury column in mm)?
  1.    H
  2.    12.6 H
  3.    13.6 H
  4.    14.6 H
 Discuss Question
Answer: Option B. -> 12.6 H
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 3183. Which of the following produces maximum pressure difference for transportation of gases ?
  1.    Vacuum pumps
  2.    Blowers
  3.    Fans
  4.    Compressors
 Discuss Question
Answer: Option D. -> Compressors
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 3184. For the production of very high vacuum, a _____________ pump is normally used?
  1.    Diffusion
  2.    Centrifugal
  3.    Jet ejector
  4.    Piston
 Discuss Question
Answer: Option A. -> Diffusion
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 3185. Navier-Stokes equation is useful in the analysis of _____________ fluid flow problems?
  1.    Non-viscous
  2.    Viscous
  3.    Turbulent
  4.    Rotational
 Discuss Question
Answer: Option B. -> Viscous
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 3186. The hydraulic diameter of an annulus of inner and outer radii Ri and Ro respectively is___________________?
  1.    4(Ro-Ri)
  2.    √(Ro-Ri)
  3.    2(Ro-Ri)
  4.    Ro + Ri
 Discuss Question
Answer: Option C. -> 2(Ro-Ri)
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 3187. A pipe has a porous section of length L as shown in the figure. Velocity at the start of this section of V0. If fluid leaks into the pipe through the porous section at a volumetric rate per unit area q(x/L)2, what will be axial velocity in the pipe at any „x‟? Assume incompressible one dimensional flow i.e., no gradients in the radial direction ?
  1.    VX = V0 + q (x3/L2D)
  2.    VX = V0 + ⅓q (x3/L2)
  3.    VX = V0 + 2q (x2/LD)
  4.    VX = V0 + (4/3) q (x3/L2D)
 Discuss Question
Answer: Option D. -> VX = V0 + (4/3) q (x3/L2D)
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 3188. Minimum fluidisation velocity for a specific system depends upon the___________________?
  1.    Particle size
  2.    Fluid viscosity
  3.    Density of both the particle & the fluid
  4.    All A., B. and C.
 Discuss Question
Answer: Option D. -> All A., B. and C.
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 3189. In case of a pipe of constant cross-sectional area, the maximum fluid velocity obtainable is___________________?
  1.    The velocity of sound
  2.    Dependent on its cross-sectional area
  3.    Dependent on fluid viscosity
  4.    Dependent on fluid density
 Discuss Question
Answer: Option A. -> The velocity of sound
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 3190. The most economical flow control valve for use with large diameter pipes is a__________________?
  1.    Butterfly valve
  2.    Globe valve
  3.    Needle valve
  4.    None of these
 Discuss Question
Answer: Option A. -> Butterfly valve
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!

Latest Videos

Latest Test Papers