Sail E0 Webinar

MCQs

Total Questions : 171 | Page 16 of 18 pages
Question 151. In screw type drafting process, combs are
  1.    perpendicular to needles
  2.    parallel to needles
  3.    at level with needles
  4.    small
 Discuss Question
Answer: Option A. -> perpendicular to needles
Answer: (a).perpendicular to needles
Question 152. Feedrack arranges slivers taken from cans on
  1.    vertical conveyor
  2.    horizontal conveyor
  3.    vertical roller
  4.    horizontal roller
 Discuss Question
Answer: Option B. -> horizontal conveyor
Answer: (b).horizontal conveyor
Question 153. In combing process, fiber is stripped from
  1.    foreign matter
  2.    short fibers and long fibers
  3.    foreign matter and short fibers
  4.    foreign matter and long fibers
 Discuss Question
Answer: Option C. -> foreign matter and short fibers
Answer: (c).foreign matter and short fibers
Question 154. Who detects volume oscillations of material fed in electronic autoleveller?
  1.    feeler
  2.    transducer
  3.    oscillator
  4.    sensory motor
 Discuss Question
Answer: Option B. -> transducer
Answer: (b).transducer
Question 155. Traditional screw type drawframes provides low production output due to
  1.    feeding ratio
  2.    lower fiber feeding ratio
  3.    low fiber control
  4.    low cleanliness
 Discuss Question
Answer: Option B. -> lower fiber feeding ratio
Answer: (b).lower fiber feeding ratio
Question 156. Drawing aggregate in lap drawing frame includes
  1.    a feeder
  2.    a fiber control device
  3.    a delivery device
  4.    all of above
 Discuss Question
Answer: Option D. -> all of above
Answer: (d).all of above
Question 157. In draft zone, fibers can be found in
  1.    1 position
  2.    2 positions
  3.    3 positions
  4.    4 positions
 Discuss Question
Answer: Option C. -> 3 positions
Answer: (c).3 positions
Question 158. Drafting set accumulated on drawframe can be categorized into
  1.    2 types
  2.    3 types
  3.    4 types
  4.    5 types
 Discuss Question
Answer: Option A. -> 2 types
Answer: (a).2 types
Question 159. Draft cylinders are made up of
  1.    metal
  2.    rubber
  3.    plastic
  4.    steel
 Discuss Question
Answer: Option D. -> steel
Answer: (d).steel
Question 160. Position of cylinders in drawframe are set using
  1.    support pivots
  2.    grid
  3.    metal sleeve
  4.    rubber bars
 Discuss Question
Answer: Option A. -> support pivots
Answer: (a).support pivots

Latest Videos
Chapter 1 - GLOBAL STEEL SCENARIO & INDIAN STEEL INDUSTRY Part 1 : (13-04-2024) INDUSTRY AND COMPANY AWARENESS (ICA)
Direction Sense Test Part 1 Reasoning (Hindi)
Chapter 1 - RMHP / OHP / OB & BP Part 1 : (14-02-2024) GPOE
Cube & Cuboid Part 1 Reasoning (Hindi)
Data Interpretation (DI) Basic Concept Reasoning (Hindi)
Counting Figures Part 1 Counting Of Straight Lines Reasoning (Hindi)
Sail E0 free webinar Webinars
Real Numbers Part 7 Class 10 Maths
Real Numbers Part 1 Class 10 Maths
Polynomials Part 1 Class 10 Maths

Latest Test Papers

GPOE / GPA Combined 1 Free Mock Test SAIL JO E-0 2024
Chapter 3.1 : INTRODUCTION Chapter 3 : Sinter Plant SAIL E0 - GPOE/GPA 2024
Chapter 2.3 : COAL HANDLING PLANT - Set 1 Chapter 2 : Coke Ovens and Coal Chemicals SAIL E0 - GPOE/GPA 2024
Chapter 1.1 : INTRODUCTION Chapter 1 : Raw Material Handling Plant SAIL E0 - GPOE/GPA 2024
DSP Combined 1 Free Revision Test SAIL JO E-0