Sail E0 Webinar

MCQs

Total Questions : 903 | Page 90 of 91 pages
Question 891. 2.  Bearing stiffeners:
  1.    are provided to distribute the load to the web.
  2.    are provided at the supports and at the points of concentrated loads.
  3.    consists of single angles on one other side of the web.
  4.    All of the above
 Discuss Question
Answer: Option D. -> All of the above
Question 892. 3.  The bearing stiffeners are designed as columns assuming the section to consist of the pair of stiffeners together with a length of web on each side of the centre line of the stiffeners where available equal to :
  1.    10 times the web thickness
  2.    15 times the web thickness
  3.    20 times the web thickness
  4.    25 times the web thickness
 Discuss Question
Answer: Option C. -> 20 times the web thickness
Question 893. 1.  Pick up the correct statement from the following
  1.    The maximum out stand of angle stiffeners from the web is 12 t
  2.    The maximum out stand of flat stiffeners from the web is 16 t
  3.    The maximum out stand of angle stiffeners from the web is 16 t
  4.    Both statements (a) and (b) are right.
 Discuss Question
Answer: Option D. -> Both statements (a) and (b) are right.
Question 894. 4.  When the thickness of the web of the girder is less than
  1.    -65
  2.    75
  3.    85
  4.    105
 Discuss Question
Answer: Option C. -> 85
Question 895. 5.  Pick up the correct statement form the following Unsupported clear dimension of a web panel shall not exceed:
  1.    250 t
  2.    225 t
  3.    275 t
  4.    300 t
 Discuss Question
Answer: Option C. -> 275 t
Question 896. 8. When the thickness of web of a plate girder is less than d/250, another horizontal stiffener is provided:
  1.    just below the upper flange
  2.    just above the lower flange
  3.    at the neutral axis
  4.    any where intension area.
 Discuss Question
Answer: Option C. -> at the neutral axis
Question 897. 7.  The horizontal stiffeners are so designed that moment of inertia I is not less than, where c1 is the actual distance between the vertical stiffeners of the girder.
  1.    2c1
  2.    3c ti
  3.    4Ci ti
  4.    4c1 ti
 Discuss Question
Answer: Option C. -> 4Ci ti
Question 898. 6.  The vertical stiffeners are spaced
  1.    greater than 1.5 d
  2.    lesser than 0.33 d
  3.    Both the statements are right
  4.    Both statements are wrong
 Discuss Question
Answer: Option D. -> Both statements are wrong
Question 899. 1.  When the thickness of the web of the girder is less than
  1.    -65
  2.    75
  3.    85
  4.    105
 Discuss Question
Answer: Option C. -> 85
Question 900. 4.  The horizontal stiffeners are so designed that moment of inertia I is not less than, where c1 is the actual distance between the vertical stiffeners of the girder.
  1.    2c1
  2.    3c ti
  3.    4Ci ti
  4.    4c1 ti
 Discuss Question
Answer: Option C. -> 4Ci ti

Latest Videos
Chapter 1 - GLOBAL STEEL SCENARIO & INDIAN STEEL INDUSTRY Part 1 : (13-04-2024) INDUSTRY AND COMPANY AWARENESS (ICA)
Direction Sense Test Part 1 Reasoning (Hindi)
Chapter 1 - RMHP / OHP / OB & BP Part 1 : (14-02-2024) GPOE
Cube & Cuboid Part 1 Reasoning (Hindi)
Data Interpretation (DI) Basic Concept Reasoning (Hindi)
Counting Figures Part 1 Counting Of Straight Lines Reasoning (Hindi)
Sail E0 free webinar Webinars
Real Numbers Part 7 Class 10 Maths
Real Numbers Part 1 Class 10 Maths
Polynomials Part 1 Class 10 Maths

Latest Test Papers

Pie Chart - Test Paper 1 Data Interpretation Reasoning & DI
Tabulation - Test Paper 2 Data Interpretation Reasoning & DI
Test Paper 1 Direction Sense Test Reasoning & DI
ICA , RDIC,GFM Free Modal Test Paper - Non - Technical Branch Old Syllabus 2022 - SAIL Junior Officer E0
GFM Combined 1 Free Revision Test SAIL JO E-0