Home
Video Series
Fast Math Tricks
Quantitative Aptitude
Class 8 Maths Videos
Class 9 Maths Videos
Class 10 Maths Videos
Reasoning Videos
Blog
Store
Register /Login
Home
Topic
Question
The creep strains are
Options:
A
.
 caused due to dead loads only
B
.
 caused due to live loads only
C
.
 caused due to cyclic loads only
D
.
 independent of loads
Answer: Option A
-NA-
Was this answer helpful ?
0 Likes
Next Question
Report Problem
Share
Submit Solution
Your email address will not be published.
Required fields are marked
*
More Questions on This Topic :
Question 1.
Two steel columns P (length L and yield strength fy = 250 MPa) and Q (length 2L and yield strength fy = 500 MPa) have t....load of column P to that of column Q is:
Question 2.
For subcritical flow in an open channel, the control section for gradually varied flow profiles is ....
Question 3.
Group-I contains dimensionless parameters and Group- II contains the ratios.Group-I Gr....dimensionless parameters in Group- I with ratios in Group-II is:
Question 4.
An isohyet is a line joining points of ....
Question 5.
Some of the water quality parameters are measured by titrating a water sample with a titrant. Group-I gives a list of p....water quality parameters in Group-I with titrants in Group-II is:
Question 6.
For a two dimensional flow field, the stream function áµ is given as áµ = 3/2(y2 - x2). The magnitude of discha....the stream lines passing through points (0,3) and (3,4) is:
Question 7.
A rectangular concrete beam 250 mm wide and 600 mm deep is pre-stressed by means of 16 high tensile wires, each of 7 mm....the beam? Neglect the effect of dead load of beam.______
Question 8.
The top width and the depth of flow in a triangular channel were measured as 4 m and 1 m, respectively. The measured ve....velocity measurement, the discharge (in m3/s) in the channel is
Question 9.
A layer of normally consolidated, saturated silty clay of 1 m thickness is subjected to one dimensional consolidation u....primary consolidation settlement (rounded off to the nearest mm) is
Question 10.
Group I contains parameters and Group II lists methods/instruments.Group I ....meterThe CORRECT match of Group I with Group II is
Latest Videos
Chapter 1 - GLOBAL STEEL SCENARIO & INDIAN STEEL INDUSTRY
Part 1 : (13-04-2024)
INDUSTRY AND COMPANY AWARENESS (ICA)
Direction Sense Test
Part 1
Reasoning (Hindi)
Chapter 1 - RMHP / OHP / OB & BP
Part 1 : (14-02-2024)
GPOE
Cube & Cuboid
Part 1
Reasoning (Hindi)
Data Interpretation (DI)
Basic Concept
Reasoning (Hindi)
Counting Figures Part 1
Counting Of Straight Lines
Reasoning (Hindi)
Sail E0 free webinar
Webinars
Real Numbers
Part 7
Class 10 Maths
Real Numbers
Part 1
Class 10 Maths
Polynomials
Part 1
Class 10 Maths
Latest Test Papers
GPOE / GPA Combined 1
Free Mock Test
SAIL JO E-0 2024
Chapter 3.1 : INTRODUCTION
Chapter 3 : Sinter Plant
SAIL E0 - GPOE/GPA 2024
Chapter 2.3 : COAL HANDLING PLANT - Set 1
Chapter 2 : Coke Ovens and Coal Chemicals
SAIL E0 - GPOE/GPA 2024
Chapter 1.1 : INTRODUCTION
Chapter 1 : Raw Material Handling Plant
SAIL E0 - GPOE/GPA 2024
DSP Combined 1
Free Revision Test
SAIL JO E-0
One click Login
Login With Google
Old way of Login
Login With Email
Submit Problem
Problem Type (Required)
Choose Problem Type
Incorrect Topic
Incomplete Question
Wrong Question
Wrong Solution
Wrong Option
Explaination : Please write a little about the issue
Submit Solution