Sail E0 Webinar

MCQs

Total Questions : 364 | Page 29 of 37 pages
Question 281. What is meant by Kaizen?
  1.    card signal
  2.    to avoid inadvertent errors
  3.    change for better quality
  4.    none of the above
 Discuss Question
Answer: Option C. -> change for better quality
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 282. Which among the following is a pull type signaling system?
  1.    Just in time
  2.    Kanban
  3.    both a. and b.
  4.    none of the above
 Discuss Question
Answer: Option C. -> both a. and b.
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 283. Imperial standard yard is made of
  1.    platinum alloy
  2.    platinum iridium alloy
  3.    bronze
  4.    all of the above
 Discuss Question
Answer: Option C. -> bronze
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 284. In which of the following length standards, parallax error is observed?
  1.    line standard
  2.    end standard
  3.    both a. and b.
  4.    none of the above
 Discuss Question
Answer: Option A. -> line standard
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 285. Which principle is used to measure distance in electronic comparator?
  1.    Frequency modulation
  2.    Radio oscillations
  3.    Both a. and b.
  4.    None of the above
 Discuss Question
Answer: Option C. -> Both a. and b.
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 286. Grade 1 is used in
  1.    high precision tasks
  2.    department of inspection
  3.    calibration of instruments
  4.    all of the above
 Discuss Question
Answer: Option B. -> department of inspection
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 287. Testing flatness or straightness of a surface is possible using
  1.    vernier caliper
  2.    micrometer
  3.    autocollimator
  4.    all of the above
 Discuss Question
Answer: Option C. -> autocollimator
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 288. Which of the following is true for interference fit?
  1.    Shaft is always smaller than the hole
  2.    Shaft is always bigger than the hole
  3.    Interference fits have shaft and hole of same dimension
  4.    None of the above
 Discuss Question
Answer: Option B. -> Shaft is always bigger than the hole
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 289. Which error is observed due to lack of squareness when depth is measured using depth micrometer?
  1.    parallax error
  2.    cosine error
  3.    sine error
  4.    all of the above
 Discuss Question
Answer: Option B. -> cosine error
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!
Question 290. Which among the following is used to create fringes in N.P.L. interferometer?
  1.    Condensing lens
  2.    Collimating lens
  3.    Optical flat
  4.    All of the above
 Discuss Question
Answer: Option C. -> Optical flat
NO EXPLANATION IS AVAILABLE FOR THIS QUESTION!

Latest Videos
Chapter 1 - GLOBAL STEEL SCENARIO & INDIAN STEEL INDUSTRY Part 1 : (13-04-2024) INDUSTRY AND COMPANY AWARENESS (ICA)
Direction Sense Test Part 1 Reasoning (Hindi)
Chapter 1 - RMHP / OHP / OB & BP Part 1 : (14-02-2024) GPOE
Cube & Cuboid Part 1 Reasoning (Hindi)
Data Interpretation (DI) Basic Concept Reasoning (Hindi)
Counting Figures Part 1 Counting Of Straight Lines Reasoning (Hindi)
Sail E0 free webinar Webinars
Real Numbers Part 7 Class 10 Maths
Real Numbers Part 1 Class 10 Maths
Polynomials Part 1 Class 10 Maths

Latest Test Papers

Chapter 3.1 : Overview of Finance & Accounts Department Chapter 3 : Finance & Accounts SAIL E0 - GFM 2024
Chapter 2.1 : Overview Chapter 2 : Materials Management SAIL E0 - GFM 2024
Chapter 1.1 : Personnel Functions- An overview Chapter 1 : Personnel Management SAIL E0 - GFM 2024
GPOE / GPA Combined 1 Free CBT Mock Test SAIL E0 2024
CBT Mixed Test 1 GPOE/GPA SAIL E0 2024