Sail E0 Webinar

MCQs

Total Questions : 540 | Page 2 of 54 pages
Question 11. The ________ tool on the dimension tool bar places the length of an arch on a drawing.
  1.     Arc Radius
  2.     Arc Length
  3.     Radius
  4.     Diameter
 Discuss Question
Answer: Option B. ->  Arc Length
Question 12. In order to create an isometric circle to represent a hole through the top surface of a box, the drafter must insure that the correct iso-plane has been selected by scrolling through the iso-planes using the ________ key.
  1.     F1
  2.     F3
  3.     F5
  4.     F8
 Discuss Question
Answer: Option C. ->  F5
Question 13. When dimensioning piping drawings, you give the lengths of all runs of this type:
  1.     Straight
  2.     Angular
  3.     Filleted
  4.     Transverse
 Discuss Question
Answer: Option A. ->  Straight
Question 14. Oblique drawings are dimensioned in a similar fashion as these types of drawings:
  1.     Orthographic
  2.     Isometric
  3.     Angular
  4.     Parallel
 Discuss Question
Answer: Option B. ->  Isometric
Question 15. Baseline dimensions are referenced from a common geometric feature known as a ________.
  1.     Edge
  2.     Corner
  3.     Datum
  4.     Point of reference
 Discuss Question
Answer: Option C. ->  Datum
Question 16. Two-point perspective is also known as:
  1.     Two-view perspective
  2.     Regular perspective
  3.     Parallel perspective
  4.     Angular perspective
 Discuss Question
Answer: Option D. ->  Angular perspective
Question 17. The principle views associated with orthographic projection are ________.
  1.     Front view
  2.     Right side view
  3.     Top view
  4.     All of the above
 Discuss Question
Answer: Option D. ->  All of the above
Question 18. The text height for room names should be set to ________for a drawing that will be plotted to a scale of ¼" = 1'-0".
  1.     4"
  2.     5"
  3.     6"
  4.     8"
 Discuss Question
Answer: Option C. ->  6"
Question 19. Placement of dimensions on a drawing is controlled by ________.
  1.     ANSI
  2.     The design engineer
  3.     Corporate drafting standards
  4.     All of the above
 Discuss Question
Answer: Option D. ->  All of the above
Question 20. The top, front, and bottom views align in this manner:
  1.     Horizontally
  2.     Vertically
  3.     According to the planar views
  4.     Parallel to the frontal plane
 Discuss Question
Answer: Option B. ->  Vertically

Latest Videos
Chapter 1 - GLOBAL STEEL SCENARIO & INDIAN STEEL INDUSTRY Part 1 : (13-04-2024) INDUSTRY AND COMPANY AWARENESS (ICA)
Direction Sense Test Part 1 Reasoning (Hindi)
Chapter 1 - RMHP / OHP / OB & BP Part 1 : (14-02-2024) GPOE
Cube & Cuboid Part 1 Reasoning (Hindi)
Data Interpretation (DI) Basic Concept Reasoning (Hindi)
Counting Figures Part 1 Counting Of Straight Lines Reasoning (Hindi)
Sail E0 free webinar Webinars
Real Numbers Part 7 Class 10 Maths
Real Numbers Part 1 Class 10 Maths
Polynomials Part 1 Class 10 Maths

Latest Test Papers

Pie Chart - Test Paper 1 Data Interpretation Reasoning & DI
Tabulation - Test Paper 2 Data Interpretation Reasoning & DI
Test Paper 1 Direction Sense Test Reasoning & DI
ICA , RDIC,GFM Free Modal Test Paper - Non - Technical Branch Old Syllabus 2022 - SAIL Junior Officer E0
GFM Combined 1 Free Revision Test SAIL JO E-0