Match the following and give the correct code given in options: Options: A . &nbspA – 1 B – 2 C – 4 B . &nbspA – 1 B – 4 C – 2 C . &nbspA – 3 B – 1 C – 2 D . &nbspA – 3 B – 4 C – 1

Match the following and give the correct code given in options:

Question

Match the following and give the correct code given in options:

Options:

A . A – 1 B – 2 C – 4

B . A – 1 B – 4 C – 2

C . A – 3 B – 1 C – 2

D . A – 3 B – 4 C – 1

Answer: Option D
Answer: (d).A – 3 B – 4 C – 1

Was this answer helpful ?

Next Question

Question 1. An axial pull of 1kN is acting on a bar of consisting two equal lengths as shown but of dia 10cm and 20cm respectively. ....the stresses in the two sections respectively in N/mm² ?

Question 2. An axial pull of 35000 N is acting on a bar consisting of two lengths as shown with their respective dimensions. What wi....the stresses in the two sections respectively in N/mm² ?

Question 3. An axial pull of 35000 N on a bar consisting of two lengths as shown with their respective dimensions. What will be the ....bar if the young’s modulus = 2.1 x 10⁵ ?

Question 4. An axial pull of 20 kN on a bar of two equal lengths of 20cm as shown with their respective dimensions. What will be the....of the bar if the young’s modulus = 2×10⁵ ?

Question 5. An axial residual compressive stress due to a manufacturing process is present on the outer surface of a rotating shaft ....in the presence of the residual compressive stress is ____________

Question 6. The length, Young’s modulus and coefficient of thermal expansion of bar P are twice that of bar Q. what will be the ra....temperature of both bars is increased by the same amount?

Question 7. A cube having each side of length p, is constrained in all directions and is heated unigormly so that the temperature is....T.C. What will be the stress developed in the cube?

Question 8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of 200kN. If the length of the....and E=200GPa, the elongation of the bar well be ____________

Question 9. A steel bar 600mm long and having 30mm diameter, is turned down to 25mm diameter for one fourth of its length. It is hea....x 10⁻⁶ per C and E = 200 GN/m²) is

Question 10. Which test is conducted to measure the endurance limit of the material?....

Chapter 1 - GLOBAL STEEL SCENARIO & INDIAN STEEL INDUSTRY Part 1 : (13-04-2024) INDUSTRY AND COMPANY AWARENESS (ICA)

Direction Sense Test Part 1 Reasoning (Hindi)

Chapter 1 - RMHP / OHP / OB & BP Part 1 : (14-02-2024) GPOE

Cube & Cuboid Part 1 Reasoning (Hindi)

Data Interpretation (DI) Basic Concept Reasoning (Hindi)

Counting Figures Part 1 Counting Of Straight Lines Reasoning (Hindi)

Sail E0 free webinar Webinars

Real Numbers Part 7 Class 10 Maths

Real Numbers Part 1 Class 10 Maths

Polynomials Part 1 Class 10 Maths

Pie Chart - Test Paper 1 Data Interpretation Reasoning & DI

Tabulation - Test Paper 2 Data Interpretation Reasoning & DI

Test Paper 1 Direction Sense Test Reasoning & DI

ICA , RDIC,GFM Free Modal Test Paper - Non - Technical Branch Old Syllabus 2022 - SAIL Junior Officer E0

GFM Combined 1 Free Revision Test SAIL JO E-0